Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138
Ano de defesa: | 2010 |
---|---|
Autor(a) principal: | |
Orientador(a): | |
Banca de defesa: | |
Tipo de documento: | Dissertação |
Tipo de acesso: | Acesso aberto |
Idioma: | por |
Instituição de defesa: |
Universidade Federal de São Carlos
|
Programa de Pós-Graduação: |
Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM
|
Departamento: |
Não Informado pela instituição
|
País: |
BR
|
Palavras-chave em Português: | |
Área do conhecimento CNPq: | |
Link de acesso: | https://repositorio.ufscar.br/handle/ufscar/809 |
Resumo: | The hot rolling process is a kind of industrial method used in raw material manufacturing for surgical implant pieces. The hot rolling processing has been the subject of many studies and the knowledge of this process is very well established. However, this process requires the control of several parameters such as the geometry of billets and rolling rolls, the initial and finishing deformation temperatures and strain rates, pass schedule, total reduction of rolling process and the capacity of the equipment. The most important feature of the metallurgical processing is the final quality of the produced material, since all parameters described above act upon processing and they can change the material behavior. Therefore, the best would be that all the process parameters were well known and controlled. The aim of this work was to analyze how the rolling processing parameters like temperature, deformation, strain rate and stress level vary during hot rolling of an ASTM F138 alloy billets. This analysis was conducted using a commercial software based on finite elements methods developed for hot work processing simulation. The processing data were attained from an industrial plant and two similar passes of a hot rolling schedule were simulated. The first pass promoted the change of a billet from a square geometry to an oval shape and the second from oval to round shape. The evolution and distribution of strain, strain rate, temperature and stress throughout the billets during hot rolling were determined and analyzed. The results showed that the numerical simulation was efficient to describe parameter evaluations, since the results are similar to those observed in a real rolling processing. The achieved results can be used as a data base for analysis of defects and failures upon processing and also to progressive improvement of the industrial processing. |
id |
SCAR_c2e8c133924206c7737feb5a880334a1 |
---|---|
oai_identifier_str |
oai:repositorio.ufscar.br:ufscar/809 |
network_acronym_str |
SCAR |
network_name_str |
Repositório Institucional da UFSCAR |
repository_id_str |
|
spelling |
Magro, Douglas StriniBalancin, Oscarhttp://lattes.cnpq.br/8379205949387493http://lattes.cnpq.br/47985295631973792016-06-02T19:12:02Z2010-08-112016-06-02T19:12:02Z2010-02-26MAGRO, Douglas Strini. Numerical simulation of hot rolling processing of ASTM F138 alloy for surgical implants. 2010. 102 f. Dissertação (Mestrado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2010.https://repositorio.ufscar.br/handle/ufscar/809The hot rolling process is a kind of industrial method used in raw material manufacturing for surgical implant pieces. The hot rolling processing has been the subject of many studies and the knowledge of this process is very well established. However, this process requires the control of several parameters such as the geometry of billets and rolling rolls, the initial and finishing deformation temperatures and strain rates, pass schedule, total reduction of rolling process and the capacity of the equipment. The most important feature of the metallurgical processing is the final quality of the produced material, since all parameters described above act upon processing and they can change the material behavior. Therefore, the best would be that all the process parameters were well known and controlled. The aim of this work was to analyze how the rolling processing parameters like temperature, deformation, strain rate and stress level vary during hot rolling of an ASTM F138 alloy billets. This analysis was conducted using a commercial software based on finite elements methods developed for hot work processing simulation. The processing data were attained from an industrial plant and two similar passes of a hot rolling schedule were simulated. The first pass promoted the change of a billet from a square geometry to an oval shape and the second from oval to round shape. The evolution and distribution of strain, strain rate, temperature and stress throughout the billets during hot rolling were determined and analyzed. The results showed that the numerical simulation was efficient to describe parameter evaluations, since the results are similar to those observed in a real rolling processing. The achieved results can be used as a data base for analysis of defects and failures upon processing and also to progressive improvement of the industrial processing.O processo de laminação a quente é um dos processos utilizados para a fabricação de matéria-prima utilizada em peças de implantes cirúrgicos. A laminação a quente tem sido objeto de muitos estudos e o conhecimento sobre este processo parece ser bem consolidado. Todavia este processo requer o controle de muitos parâmetros, como a geometria dos tarugos e dos cilindros de laminação, a relação entre os cilindros e o tarugo, a temperatura e velocidade de laminação, plano de passes, redução total de laminação, capacidade máxima do equipamento, entre outros. O mais importante do processo acaba se tornando a qualidade final do material produzido, pois todos os parâmetros descritos acima variam, e estas variações não podem impactar negativamente na qualidade do produto final. Assim o ideal seria que todos os parâmetros de processo fossem bem conhecidos e controlados. O objetivo deste trabalho foi analisar como parâmetros do processo de laminação tais como temperatura, deformação, taxa de deformação e tensão aplicada variam durante a laminação de um tarugo da liga ASTM F138 utilizando um software comercial, desenvolvido para análises de processo de conformação com base nos métodos dos elementos finitos. Foram simulados dois passes de laminação semelhantes aos que ocorrem em um processo real, sendo o primeiro passe quadrado-oval e outro oval-redondo. Foi analisada a variação dos parâmetros ao longo do tarugo durante a laminação. Os resultados mostraram que a simulação numérica foi eficiente em avaliar os parâmetros investigados, pois os resultados obtidos são semelhantes aos encontrados em um processo real de laminação. Estes dados encontrados com a ajuda de um software de simulação servirão como base de estudos para análise de defeitos e também da melhoria contínua de processo.application/pdfporUniversidade Federal de São CarlosPrograma de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEMUFSCarBRConformação de metaisSimulação numéricaImplantes artificiaisNormas técnicasENGENHARIAS::ENGENHARIA DE MATERIAIS E METALURGICASimulação numérica de laminação da liga para implantes cirúrgicos ASTM F138Numerical simulation of hot rolling processing of ASTM F138 alloy for surgical implantsinfo:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFSCARinstname:Universidade Federal de São Carlos (UFSCAR)instacron:UFSCARORIGINAL3138.pdfapplication/pdf2797122https://{{ getenv "DSPACE_HOST" "repositorio.ufscar.br" }}/bitstream/ufscar/809/1/3138.pdfda6799e838cbdb9cbde4d35e501f2ebdMD51THUMBNAIL3138.pdf.jpg3138.pdf.jpgIM Thumbnailimage/jpeg6034https://{{ getenv "DSPACE_HOST" "repositorio.ufscar.br" }}/bitstream/ufscar/809/2/3138.pdf.jpg715ef7f3e2480b81079c6d98e55bef90MD52ufscar/8092020-03-23 19:54:20.434oai:repositorio.ufscar.br:ufscar/809Repositório InstitucionalPUBhttps://repositorio.ufscar.br/oai/requestopendoar:43222023-05-25T12:43:45.110200Repositório Institucional da UFSCAR - Universidade Federal de São Carlos (UFSCAR)false |
dc.title.por.fl_str_mv |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
dc.title.alternative.eng.fl_str_mv |
Numerical simulation of hot rolling processing of ASTM F138 alloy for surgical implants |
title |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
spellingShingle |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 Magro, Douglas Strini Conformação de metais Simulação numérica Implantes artificiais Normas técnicas ENGENHARIAS::ENGENHARIA DE MATERIAIS E METALURGICA |
title_short |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
title_full |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
title_fullStr |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
title_full_unstemmed |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
title_sort |
Simulação numérica de laminação da liga para implantes cirúrgicos ASTM F138 |
author |
Magro, Douglas Strini |
author_facet |
Magro, Douglas Strini |
author_role |
author |
dc.contributor.authorlattes.por.fl_str_mv |
http://lattes.cnpq.br/4798529563197379 |
dc.contributor.author.fl_str_mv |
Magro, Douglas Strini |
dc.contributor.advisor1.fl_str_mv |
Balancin, Oscar |
dc.contributor.advisor1Lattes.fl_str_mv |
http://lattes.cnpq.br/8379205949387493 |
contributor_str_mv |
Balancin, Oscar |
dc.subject.por.fl_str_mv |
Conformação de metais Simulação numérica Implantes artificiais Normas técnicas |
topic |
Conformação de metais Simulação numérica Implantes artificiais Normas técnicas ENGENHARIAS::ENGENHARIA DE MATERIAIS E METALURGICA |
dc.subject.cnpq.fl_str_mv |
ENGENHARIAS::ENGENHARIA DE MATERIAIS E METALURGICA |
description |
The hot rolling process is a kind of industrial method used in raw material manufacturing for surgical implant pieces. The hot rolling processing has been the subject of many studies and the knowledge of this process is very well established. However, this process requires the control of several parameters such as the geometry of billets and rolling rolls, the initial and finishing deformation temperatures and strain rates, pass schedule, total reduction of rolling process and the capacity of the equipment. The most important feature of the metallurgical processing is the final quality of the produced material, since all parameters described above act upon processing and they can change the material behavior. Therefore, the best would be that all the process parameters were well known and controlled. The aim of this work was to analyze how the rolling processing parameters like temperature, deformation, strain rate and stress level vary during hot rolling of an ASTM F138 alloy billets. This analysis was conducted using a commercial software based on finite elements methods developed for hot work processing simulation. The processing data were attained from an industrial plant and two similar passes of a hot rolling schedule were simulated. The first pass promoted the change of a billet from a square geometry to an oval shape and the second from oval to round shape. The evolution and distribution of strain, strain rate, temperature and stress throughout the billets during hot rolling were determined and analyzed. The results showed that the numerical simulation was efficient to describe parameter evaluations, since the results are similar to those observed in a real rolling processing. The achieved results can be used as a data base for analysis of defects and failures upon processing and also to progressive improvement of the industrial processing. |
publishDate |
2010 |
dc.date.available.fl_str_mv |
2010-08-11 2016-06-02T19:12:02Z |
dc.date.issued.fl_str_mv |
2010-02-26 |
dc.date.accessioned.fl_str_mv |
2016-06-02T19:12:02Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.citation.fl_str_mv |
MAGRO, Douglas Strini. Numerical simulation of hot rolling processing of ASTM F138 alloy for surgical implants. 2010. 102 f. Dissertação (Mestrado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2010. |
dc.identifier.uri.fl_str_mv |
https://repositorio.ufscar.br/handle/ufscar/809 |
identifier_str_mv |
MAGRO, Douglas Strini. Numerical simulation of hot rolling processing of ASTM F138 alloy for surgical implants. 2010. 102 f. Dissertação (Mestrado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2010. |
url |
https://repositorio.ufscar.br/handle/ufscar/809 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de São Carlos |
dc.publisher.program.fl_str_mv |
Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM |
dc.publisher.initials.fl_str_mv |
UFSCar |
dc.publisher.country.fl_str_mv |
BR |
publisher.none.fl_str_mv |
Universidade Federal de São Carlos |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFSCAR instname:Universidade Federal de São Carlos (UFSCAR) instacron:UFSCAR |
instname_str |
Universidade Federal de São Carlos (UFSCAR) |
instacron_str |
UFSCAR |
institution |
UFSCAR |
reponame_str |
Repositório Institucional da UFSCAR |
collection |
Repositório Institucional da UFSCAR |
bitstream.url.fl_str_mv |
https://{{ getenv "DSPACE_HOST" "repositorio.ufscar.br" }}/bitstream/ufscar/809/1/3138.pdf https://{{ getenv "DSPACE_HOST" "repositorio.ufscar.br" }}/bitstream/ufscar/809/2/3138.pdf.jpg |
bitstream.checksum.fl_str_mv |
da6799e838cbdb9cbde4d35e501f2ebd 715ef7f3e2480b81079c6d98e55bef90 |
bitstream.checksumAlgorithm.fl_str_mv |
MD5 MD5 |
repository.name.fl_str_mv |
Repositório Institucional da UFSCAR - Universidade Federal de São Carlos (UFSCAR) |
repository.mail.fl_str_mv |
|
_version_ |
1767351056559243264 |