Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável
Ano de defesa: | 2017 |
---|---|
Autor(a) principal: | |
Orientador(a): | |
Banca de defesa: | |
Tipo de documento: | Dissertação |
Tipo de acesso: | Acesso aberto |
Idioma: | por |
Instituição de defesa: |
Universidade Federal da Paraíba
Brasil Odontologia Programa de Pós-Graduação em Odontologia UFPB |
Programa de Pós-Graduação: |
Não Informado pela instituição
|
Departamento: |
Não Informado pela instituição
|
País: |
Não Informado pela instituição
|
Palavras-chave em Português: | |
Link de acesso: | https://repositorio.ufpb.br/jspui/handle/123456789/14944 |
Resumo: | Introduction: The incorporation of antimicrobial agents to the acrylic resin is an alternative strategy to prevent or treat fungal infections, however, it is important that these materials do not modify the physical characteristics of the final product. Purpose: To evaluate the incorporation of the cerium nitrate on the flexural strength and surface roughness of the acrylic resin thermally activated by microwave energy (Vipi Wave). Materials and Methods: Cerium nitrate solutions were obtained in two types of solvents (10% DMSO and 5% DMSO + 5% Tween 80) in two concentrates (16xCIM: 26 mg/ml and 32xCIM: 52mg/ml), which were incorporated, creating five groups: Control Group (pure PPMA), DMSO + Cerium 16xCIM (DC 16xCIM) and 32xCIM (DC 32xCIM) and DMSO + Tween + Cerium 16xCIM (DTC 16xCIM) and 32Xcim (DTC 32Xcim). The solutions were incorporated into the thermo-polymerizable acrylic resin to develop the test specimens, elaborated according to ISO 20795-1 / 2013. The specimens were submitted to the flexural strength test at three points (n = 17), roughness analysis (Sa and Sz) by using optical profilometry (n = 19) and percentage of porosity (n=18) in x-ray computed microtomography (micro CT). The statistic analysis was performed in the IBM SPSS software (21.0). The results of flexural strength and surface roughness were analyzed by ANOVA and in complement, the Tukey test adopting a significance level of 1% (α=0.01). The porosity results was analyzed by Kruskal-Wallis e Mann Whitney U adopting a significance level of 1% (α=0.01). Results: In the flexural tests it was found that the experimental groups demonstrated a less resistance than control group (80,66 MPa; DP 11,30) (p<0.0001), with no statistics difference among themselves. In the statistical analysis of the surface roughness it was observed that all groups showed an increase in roughness in relation to the control (Sa 0,057µm; Sz 0,585µm) (p<0.01), except the DTC 32xCIM group (Sa 0,087µm, Sz 0,627µm). The porosity of the experimental groups was statistically higher than the control group (p<0,01). Conclusion: The incorporation of cerium nitrate resulted in reduction of flexural strength, in an increase of porosity, and the increase of surface roughness of the acrylic resin tested in all groups, except the DTC 32xCIM, despite this, the surface roughness values where is in the acceptable limit established in the literature. |
id |
UFPB_0f839d289fd559e14f5455ebcd1de26d |
---|---|
oai_identifier_str |
oai:repositorio.ufpb.br:123456789/14944 |
network_acronym_str |
UFPB |
network_name_str |
Biblioteca Digital de Teses e Dissertações da UFPB |
repository_id_str |
|
spelling |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizávelPolimetilmetacrilatoCérioPropriedades físicasPolymethyl methacrylateCeriumPhysical propertiesCNPQ::CIENCIAS DA SAUDE::ODONTOLOGIAIntroduction: The incorporation of antimicrobial agents to the acrylic resin is an alternative strategy to prevent or treat fungal infections, however, it is important that these materials do not modify the physical characteristics of the final product. Purpose: To evaluate the incorporation of the cerium nitrate on the flexural strength and surface roughness of the acrylic resin thermally activated by microwave energy (Vipi Wave). Materials and Methods: Cerium nitrate solutions were obtained in two types of solvents (10% DMSO and 5% DMSO + 5% Tween 80) in two concentrates (16xCIM: 26 mg/ml and 32xCIM: 52mg/ml), which were incorporated, creating five groups: Control Group (pure PPMA), DMSO + Cerium 16xCIM (DC 16xCIM) and 32xCIM (DC 32xCIM) and DMSO + Tween + Cerium 16xCIM (DTC 16xCIM) and 32Xcim (DTC 32Xcim). The solutions were incorporated into the thermo-polymerizable acrylic resin to develop the test specimens, elaborated according to ISO 20795-1 / 2013. The specimens were submitted to the flexural strength test at three points (n = 17), roughness analysis (Sa and Sz) by using optical profilometry (n = 19) and percentage of porosity (n=18) in x-ray computed microtomography (micro CT). The statistic analysis was performed in the IBM SPSS software (21.0). The results of flexural strength and surface roughness were analyzed by ANOVA and in complement, the Tukey test adopting a significance level of 1% (α=0.01). The porosity results was analyzed by Kruskal-Wallis e Mann Whitney U adopting a significance level of 1% (α=0.01). Results: In the flexural tests it was found that the experimental groups demonstrated a less resistance than control group (80,66 MPa; DP 11,30) (p<0.0001), with no statistics difference among themselves. In the statistical analysis of the surface roughness it was observed that all groups showed an increase in roughness in relation to the control (Sa 0,057µm; Sz 0,585µm) (p<0.01), except the DTC 32xCIM group (Sa 0,087µm, Sz 0,627µm). The porosity of the experimental groups was statistically higher than the control group (p<0,01). Conclusion: The incorporation of cerium nitrate resulted in reduction of flexural strength, in an increase of porosity, and the increase of surface roughness of the acrylic resin tested in all groups, except the DTC 32xCIM, despite this, the surface roughness values where is in the acceptable limit established in the literature.NenhumaIntrodução: A incorporação de agentes antimicrobianos à resina acrílica é uma estratégia alternativa para previnir ou tratar infecções fúngicas, entretanto é importante que esses antimicrobianos não alterem as características físicas do produto final. Objetivo: Avaliar o efeito da incorporação da solução de nitrato de cério na resistência à flexão, rugosidade superficial e porosidade da resina acrílica termicamente ativada por energia de micro-ondas (Vipi Wave). Materiais e Métodos: Foram obtidas soluções de nitrato de cério em dois tipos de solventes (DMSO 10% e DMSO 5% + Tween 80 5%), em duas concentrações (16xCIM: 26 mg/mL e 32xCIM: 52 mg/mL) as quais foram incorporadas, formando cinco grupos: Grupo Controle (PPMA puro), DMSO+Cério 16xCIM (DC 16xCIM) e 32xCIM (DC 32xCIM) e DMSO+Tween+Cério 16xCIM (DTC 16xCIM) e 32xCIM (DTC 32xCIM). As soluções foram incorporadas à resina acrílica termopolimerizável para a confecção de corpos de prova elaborados segundo a ISO 20795-1/2013. Os espécimes foram submetidos ao teste de resistência a flexão de três pontos (n=17) e análise da rugosidade (Sa e Sz) por meio de perfilometria óptica (n=19) e avaliação do percentual de porosidade (n=18) através de micro tomografia computadorizada (micro-CT). A análise estatística foi realizada no software IBM SPSS (21.0). Os valores médios dos ensaios de flexão e rugosidade foram avaliados por ANOVA com complementação do Teste de Tukey, adotando-se um nível de significância de 1% (α=0,01). A porosidade foi analisada por Kruskal-Wallis e Mann Whitney U, com nível de significância de 1% (α=0,01). Resultados: Nos testes de flexão foi encontrado que todos os grupos experimentais apresentaram uma menor resistência em relação ao grupo controle (80,66 MPa; DP 11,30) (p<0,001),sem diferenças estatísticas entre si. Na análise estatística da rugosidade superficial foi observado que todos os grupos apresentaram aumento da rugosidade superficial em relação ao controle (Sa 0,057µm; Sz 0,585µm) (p<0,01), exceto o grupo DTC 32xCIM (Sa 0,087µm; Sz 0,627µm). A porosidade dos grupos experimentais apresentou-se estatisticamente maior que o grupo controle (p<0,01). Conclusão: A incorporação do nitrato de cério resultou na diminuição da resistência à flexão; aumento da porosidade e aumento da rugosidade superficial da resina acrílica testada em todos os grupos, exceto no DTC 32xCIM, apesar disso, os valores da rugosidade superficial se encontram dentro do limite aceitável estabelecido pela literatura.Universidade Federal da ParaíbaBrasilOdontologiaPrograma de Pós-Graduação em OdontologiaUFPBBatista, André Ulisses Dantashttp://lattes.cnpq.br/9510942902249475Farias, Ohana Rodrigues2019-07-02T17:04:05Z2019-07-022019-07-02T17:04:05Z2017-12-13info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesishttps://repositorio.ufpb.br/jspui/handle/123456789/14944porAttribution-NoDerivs 3.0 Brazilhttp://creativecommons.org/licenses/by-nd/3.0/br/info:eu-repo/semantics/openAccessreponame:Biblioteca Digital de Teses e Dissertações da UFPBinstname:Universidade Federal da Paraíba (UFPB)instacron:UFPB2019-07-03T06:06:12Zoai:repositorio.ufpb.br:123456789/14944Biblioteca Digital de Teses e Dissertaçõeshttps://repositorio.ufpb.br/PUBhttp://tede.biblioteca.ufpb.br:8080/oai/requestdiretoria@ufpb.br|| diretoria@ufpb.bropendoar:2019-07-03T06:06:12Biblioteca Digital de Teses e Dissertações da UFPB - Universidade Federal da Paraíba (UFPB)false |
dc.title.none.fl_str_mv |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
title |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
spellingShingle |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável Farias, Ohana Rodrigues Polimetilmetacrilato Cério Propriedades físicas Polymethyl methacrylate Cerium Physical properties CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
title_short |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
title_full |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
title_fullStr |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
title_full_unstemmed |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
title_sort |
Efeito da incorporação do nitrato de cério na resistência à flexão, rugosidade superficial e porosidade de uma resina acrílica termopolimerizável |
author |
Farias, Ohana Rodrigues |
author_facet |
Farias, Ohana Rodrigues |
author_role |
author |
dc.contributor.none.fl_str_mv |
Batista, André Ulisses Dantas http://lattes.cnpq.br/9510942902249475 |
dc.contributor.author.fl_str_mv |
Farias, Ohana Rodrigues |
dc.subject.por.fl_str_mv |
Polimetilmetacrilato Cério Propriedades físicas Polymethyl methacrylate Cerium Physical properties CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
topic |
Polimetilmetacrilato Cério Propriedades físicas Polymethyl methacrylate Cerium Physical properties CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
description |
Introduction: The incorporation of antimicrobial agents to the acrylic resin is an alternative strategy to prevent or treat fungal infections, however, it is important that these materials do not modify the physical characteristics of the final product. Purpose: To evaluate the incorporation of the cerium nitrate on the flexural strength and surface roughness of the acrylic resin thermally activated by microwave energy (Vipi Wave). Materials and Methods: Cerium nitrate solutions were obtained in two types of solvents (10% DMSO and 5% DMSO + 5% Tween 80) in two concentrates (16xCIM: 26 mg/ml and 32xCIM: 52mg/ml), which were incorporated, creating five groups: Control Group (pure PPMA), DMSO + Cerium 16xCIM (DC 16xCIM) and 32xCIM (DC 32xCIM) and DMSO + Tween + Cerium 16xCIM (DTC 16xCIM) and 32Xcim (DTC 32Xcim). The solutions were incorporated into the thermo-polymerizable acrylic resin to develop the test specimens, elaborated according to ISO 20795-1 / 2013. The specimens were submitted to the flexural strength test at three points (n = 17), roughness analysis (Sa and Sz) by using optical profilometry (n = 19) and percentage of porosity (n=18) in x-ray computed microtomography (micro CT). The statistic analysis was performed in the IBM SPSS software (21.0). The results of flexural strength and surface roughness were analyzed by ANOVA and in complement, the Tukey test adopting a significance level of 1% (α=0.01). The porosity results was analyzed by Kruskal-Wallis e Mann Whitney U adopting a significance level of 1% (α=0.01). Results: In the flexural tests it was found that the experimental groups demonstrated a less resistance than control group (80,66 MPa; DP 11,30) (p<0.0001), with no statistics difference among themselves. In the statistical analysis of the surface roughness it was observed that all groups showed an increase in roughness in relation to the control (Sa 0,057µm; Sz 0,585µm) (p<0.01), except the DTC 32xCIM group (Sa 0,087µm, Sz 0,627µm). The porosity of the experimental groups was statistically higher than the control group (p<0,01). Conclusion: The incorporation of cerium nitrate resulted in reduction of flexural strength, in an increase of porosity, and the increase of surface roughness of the acrylic resin tested in all groups, except the DTC 32xCIM, despite this, the surface roughness values where is in the acceptable limit established in the literature. |
publishDate |
2017 |
dc.date.none.fl_str_mv |
2017-12-13 2019-07-02T17:04:05Z 2019-07-02 2019-07-02T17:04:05Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
https://repositorio.ufpb.br/jspui/handle/123456789/14944 |
url |
https://repositorio.ufpb.br/jspui/handle/123456789/14944 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
Attribution-NoDerivs 3.0 Brazil http://creativecommons.org/licenses/by-nd/3.0/br/ info:eu-repo/semantics/openAccess |
rights_invalid_str_mv |
Attribution-NoDerivs 3.0 Brazil http://creativecommons.org/licenses/by-nd/3.0/br/ |
eu_rights_str_mv |
openAccess |
dc.publisher.none.fl_str_mv |
Universidade Federal da Paraíba Brasil Odontologia Programa de Pós-Graduação em Odontologia UFPB |
publisher.none.fl_str_mv |
Universidade Federal da Paraíba Brasil Odontologia Programa de Pós-Graduação em Odontologia UFPB |
dc.source.none.fl_str_mv |
reponame:Biblioteca Digital de Teses e Dissertações da UFPB instname:Universidade Federal da Paraíba (UFPB) instacron:UFPB |
instname_str |
Universidade Federal da Paraíba (UFPB) |
instacron_str |
UFPB |
institution |
UFPB |
reponame_str |
Biblioteca Digital de Teses e Dissertações da UFPB |
collection |
Biblioteca Digital de Teses e Dissertações da UFPB |
repository.name.fl_str_mv |
Biblioteca Digital de Teses e Dissertações da UFPB - Universidade Federal da Paraíba (UFPB) |
repository.mail.fl_str_mv |
diretoria@ufpb.br|| diretoria@ufpb.br |
_version_ |
1797057852488024064 |